Experimental Investigation of the Effects of Electrodes on EDM Hole Drilling Process, pages: 377-382

Kürşad GÖV

Özet


In this experimental comparative study, holes were machined to the DIN 1.2379 die steel by using Electrical Discharge Hole Drilling (EDHD) method. The effect of the different electrode materials, channel type and machining current on EDHD performance was investigated. In the experiment, single and multi-channel brass and copper electrodes were used. The performance parameters were defined as machining speed (MS), electrode wear (EW), surface roughness (Ra) and white layer thickness (WLT). The experimental results reveal that the single-channel brass electrode has comparatively better MS and lower EW then the multi-channel brass and copper electrodes. Also, the surface quality and WLT of the single-channel brass electrode has the better values then the others.


Anahtar Kelimeler


EDHD, Machining Speed, Electrode Wear, Surface Roughness, White Layer Thickness

Referanslar


Sommer, C. and S. Sommer, "Complete EDM handbook". Advance Pub., (2005).

Gov, K. "Experimental Investigation of The Effects of The Coolant on The Performance Parameters of Electrical Discharge Drilling of Some Aerospace Materials", Journal of The Faculty of Engineering and Architecture of Gazi University, 32(1): (2017).

Gov, K. "The effects of the dielectric liquid temperature on the hole geometries drilled by electro erosion", The International Journal of Advanced Manufacturing Technology, (2017).

Göv, K. "Influence of the Coolant on Performance of Electro Discharge Hole Drilling", Journal of Polytechnic, 20(1): 191-196, (2017).

Yusuf Keskin, H., H. Selcuk, and K. Mevlut. "An experimental study for determination of the effects of machining parameters on surface roughness in EDM", International Journal of Advance Manufacturing Technology, 28: 1118-1121, (2006).

Puranik, M.S. and S.S. Joshi. "Analysis of accuracy of high-aspect-ratio holes generated using micro-electric discharge machining drilling", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 222(11): 1453-1464, (2008).

Mujumdar, S.S., S.A. Mastud, R.K. Singh, and S.S. Joshi. "Experimental characterization of the reverse micro-electrodischarge machining process for fabrication of high-aspect-ratio micro-rod arrays", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 224(5): 777-794, (2010).

Kurnia, W., P.C. Tan, S.H. Yeo, and Q.P. Tan. "Surface roughness model for micro electrical discharge machining", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 223(3): 279-287, (2009).

Yilmaz, O. and M.A. Okka. "Effect of single and multi-channel electrodes application on EDM fast hole drilling performance", The International Journal of Advanced Manufacturing Technology, 51(1-4): 185-194, (2010).

Kuppan, P., A. Rajadurai, and S. Narayanan. "Influence of EDM process parameters in deep hole drilling of Inconel 718", The International Journal of Advanced Manufacturing Technology, 38(1-2): 74-84, (2008).

Singh, P.N., K. Raghukandan, M. Rathinasabapathi, and B. Pai. "Electric discharge machining of Al–10% SiC p as-cast metal matrix composites", Journal of materials processing technology, 155: 1653-1657, (2004).

Ekmekci, B., A. Sayar, T.T. Öpöz, and A. Erden. "Geometry and surface damage in micro electrical discharge machining of micro-holes", Journal of Micromechanics and Microengineering, 19(10): 105030, (2009).

Yadav, U.S. and V. Yadava. "Experimental investigation on electrical discharge diamond drilling of nickel-based superalloy aerospace material", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, (2015).

Janmanee, P. and A. Muttamara. "A study of hole drilling on stainless steel AISI 431 by EDM using brass tube electrode", International Transaction Journal of Engineering, Management, & Applied Sciences & Technologies, 2(4): 471-481, (2011).

Gov, K. "Investigation of the Effects of the Dissolved Oxygen in the Coolant on the Hole Geometries Drilled by Electro Erosion", Journal of The Faculty of Engineering and Architecture of Gazi University, 31(2): 231-239, (2016).

Çogun, C., B. Özerkan, and T. Karaçay. "An experimental investigation on the effect of powder mixed dielectric on machining performance in electric discharge machining", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 220(7): 1035-1050, (2006).

Ekmekci, B., F. Ulusöz, N. Ekmekci, and H. Yaşar. "Suspended SiC particle deposition on plastic mold steel surfaces in powder-mixed electrical discharge machining", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 229(3): 475-486, (2015).

Ergün, Z.E. and C. Çoğun. "Elektro Erozyon ile İşleme (EEİ) İş Parçasi Yüzey Karakteristiklerinin Deneysel İncelenmesi", Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi, 21(3): (2006).

Khan, A.A. "Electrode wear and material removal rate during EDM of aluminum and mild steel using copper and brass electrodes", The International Journal of Advanced Manufacturing Technology, 39(5-6): 482-487, (2008).

Hasçalık, A. and U. Çaydaş. "Electrical discharge machining of titanium alloy (Ti–6Al–4V)", Applied Surface Science, 253(22): 9007-9016, (2007).


Tam Metin: PDF (English)

Refback'ler

  • Şu halde refbacks yoktur.



Politeknik Dergisi © 2014

P-ISSN 1302-0900    E-ISSN 2147-9429